eco-friendly raindrop inquire now for workhouse

Company Advantages
1. Every detail of Redwave polycarbonate sheet cut to size is delicately designed and carefully manufactured.
2. The product is of good quality and reliable.
3. The product quality is reliable, the performance is stable, the service life is long.
4. Guangdong Hongbo Building Materials Science and Technology Co., Ltd. will firmly observe the principle of ' Customers First'.
5. As polycarbonate sheet cut to size technology widespreadly applied, Guangdong Hongbo Building Materials Science and Technology Co., Ltd. 's research and development capabilities is improved.

Product Introduction：

Redwave polycarbonate hollow sheet is made from virgin polycarbonate material and the high concentration UV coextrusion. The sheet possesses the features of light in weight, pervious to light, impact resistance, heat isolation, flame retardant, endurance, etc.

In addition to the above features, Crystal PC hollow sheet is with the effect of “glittering and translucent” making the light penetration downier with better aesthetic visual effect.

 

Best feature of the product：UV co-extrusion process for resistance of yellowing, sound insulation, heat preservation, safe and transparent.

 

Scope of Application:

Skylight roof commercial building, residential building,factory building, warehouse, indoor stadium, advertising board, motor shed, partitions for swimming pool,

greenhouse and indoor chamber, decoration and exhibition.

 

Product Specification:

Standard width： 2100mm 、1220mm ( available for thickness 4mm to 8mm only )

Standard thickness： 4.0mm、6.0mm、8.0mm、10.0mm、12.0mm、14.0mm、16.0mm ( 4 ~ 10 mm is the rectangular structure with twin wall,

12 ~ 16 mm is the rectangular structure with triple wall)

Standard lengt： 5800mm ; 11800mm

Color： transparent, grass green, opal ,blue, bronze

Installation guide：

 

1.1  Installation by inserting

A.Because the protective film inserted in supporting frame has a bad affect on adhesion between crack filler and PC panels, protective film 5-10mm wide inserted should be cut off before PC products are inserted.

B.Because the PC panels don't change in the same range when expand with heat and shrink with cold as metal frame, and they can be bent to some extent and resit air pressure, You must take the following factors into consideration: suitable quantity inserted, the space allowing their expanding or shrinking with the change of temperature and right thickness of PC panels.

1.2Installation by screws:

A.For any outdoor installation or installation in environment with temperature difference of 8℃,enlarge the aperture of any bolt or rivet much be enlarged to allow PC panels expanding or shrinking with change of temperature. Generally, the aperture shall be 50% bigger than the diameter of bolt. Use aluminum rivet. Self-drilling screw must be abandoned.

B.Use silica gel to fill all apertures and cover their exposing parts to prevent PC panels from map cracking by cleanser which may inserted in apertures.

C.The head of rivet should be 1.5-2.0 times bigger that the stem. Use gasket to fill between PC panels and rivet head to prevent PC panels getting directs pressure from rivet head, then lessen their pressure in this way.

D.Don't tighten screw too much in case stress may cause thereof.

E.Don't use PVC gasket and water-proof adhesive tape with asphalt content .

F.Fix the metal pressing strip on long and short edges of PC panels. Remain a space for their expanding. Strengthen installation stability

Limitation to know :

Keep PC panels away from wet cement surface or any acid or base materials.

Keep PC panels away from any organic solvent or any glue or paint composing of organic solvent.

Keep frame clean and jointing groove flat and smooth .

Choose right thickness of PC panels,allow flexure radius .

Remain space for expanding , pay attention to inserting depth. Don’t know drill any hole in curved part of sheet.

Use only neutral silica gel and use only EPDM rubber strip or washer as sealant.

Use electrical tools (tungsten carbide saw )to cut; During cutting, stabilize

PC panels to prevent their vibration and never pill off protective film .

In case that marks have to be made before cutting,try to mark on protective

film;If the marks must be made directly on PC panels,use wax crayon instead

of any sharp tool to mark .

Never pill off protective films until installation is completed .

Company Features
1. Guangdong Hongbo Building Materials Science and Technology Co., Ltd. is widely known as a reliable and professional manufacturer.
2. Redwave uses imported technology to help optimize plexiglass sheets .
3. In addition to seeking business development, we still strive to make a positive impact on our local communities. We use locally based resources rather than outsourcing them, hence, in this way, we can protect the home-grown jobs. Inquiry! Being a responsible member of the global community has been woven into all aspects of our company culture. Our team works collaboratively with organizations to build awareness of environmental concerns and enhance environmental performance.