Company Advantages
1. In order to capture the market opportunities,Guangdong Hongbo Building Materials Science and Technology Co., Ltd. adopt the most cutting edge technique in China. Redwave products feature insulations of sound and heat
2. The product has to be tested before coming into the market to ensure it meets all national and international regulations, giving you an assurance in its safety and overall performance. Environmental friendliness is a focus during the manufacturing
3. Every aspect of the pricing and availability of the polycarbonate roofing sheets in polycarbonate roof sheeting prices had been calculated to make it a highly sought product. The manufacturing is wholly automated

Product Introduction：

Redwave polycarbonate hollow sheet is made from virgin polycarbonate material and the high concentration UV coextrusion. The sheet possesses the features of light in weight, pervious to light, impact resistance, heat isolation, flame retardant, endurance, etc.

In addition to the above features, Crystal PC hollow sheet is with the effect of “glittering and translucent” making the light penetration downier with better aesthetic visual effect.

 

Best feature of the product：UV co-extrusion process for resistance of yellowing, sound insulation, heat preservation, safe and transparent.

 

Scope of Application:

Skylight roof commercial building, residential building,factory building, warehouse, indoor stadium, advertising board, motor shed, partitions for swimming pool,

greenhouse and indoor chamber, decoration and exhibition.

 

Product Specification:

Standard width： 2100mm 、1220mm ( available for thickness 4mm to 8mm only )

Standard thickness： 4.0mm、6.0mm、8.0mm、10.0mm、12.0mm、14.0mm、16.0mm ( 4 ~ 10 mm is the rectangular structure with twin wall,

12 ~ 16 mm is the rectangular structure with triple wall)

Standard lengt： 5800mm ; 11800mm

Color： transparent, grass green, opal ,blue, bronze

Installation guide：

 

1.1  Installation by inserting

A.Because the protective film inserted in supporting frame has a bad affect on adhesion between crack filler and PC panels, protective film 5-10mm wide inserted should be cut off before PC products are inserted.

B.Because the PC panels don't change in the same range when expand with heat and shrink with cold as metal frame, and they can be bent to some extent and resit air pressure, You must take the following factors into consideration: suitable quantity inserted, the space allowing their expanding or shrinking with the change of temperature and right thickness of PC panels.

1.2Installation by screws:

A.For any outdoor installation or installation in environment with temperature difference of 8℃,enlarge the aperture of any bolt or rivet much be enlarged to allow PC panels expanding or shrinking with change of temperature. Generally, the aperture shall be 50% bigger than the diameter of bolt. Use aluminum rivet. Self-drilling screw must be abandoned.

B.Use silica gel to fill all apertures and cover their exposing parts to prevent PC panels from map cracking by cleanser which may inserted in apertures.

C.The head of rivet should be 1.5-2.0 times bigger that the stem. Use gasket to fill between PC panels and rivet head to prevent PC panels getting directs pressure from rivet head, then lessen their pressure in this way.

D.Don't tighten screw too much in case stress may cause thereof.

E.Don't use PVC gasket and water-proof adhesive tape with asphalt content .

F.Fix the metal pressing strip on long and short edges of PC panels. Remain a space for their expanding. Strengthen installation stability

Limitation to know :

Keep PC panels away from wet cement surface or any acid or base materials.

Keep PC panels away from any organic solvent or any glue or paint composing of organic solvent.

Keep frame clean and jointing groove flat and smooth .

Choose right thickness of PC panels,allow flexure radius .

Remain space for expanding , pay attention to inserting depth. Don’t know drill any hole in curved part of sheet.

Use only neutral silica gel and use only EPDM rubber strip or washer as sealant.

Use electrical tools (tungsten carbide saw )to cut; During cutting, stabilize

PC panels to prevent their vibration and never pill off protective film .

In case that marks have to be made before cutting,try to mark on protective

film;If the marks must be made directly on PC panels,use wax crayon instead

of any sharp tool to mark .

Never pill off protective films until installation is completed .

Company Features
1. Over the years, Redwave has won high brand popularity by its fabulous .
2. Our professional technician strictly operate machines to ensure its normal operation and produce high quality polycarbonate roofing sheets.
3. Guangdong Hongbo Building Materials Science and Technology Co., Ltd. seeks to structure polycarbonate roof sheeting prices as its service creed. Check now!